COVNA HK60-Q-3PS Series Electric Ball Valve

Technical Parameter of Actuators: 

Model	5	10	16	30	60	125	250	400
Torque Output	50Nm	100Nm	160Nm	300Nm	600Nm	1250Nm	2500Nm	4000Nm
90°Cycle Time	20s/60s	15s/30s/60s	15s/30s	15s/30s	30s/60s	100s	100s	100s
Angle of Rotation	0-90°	0-90°	0-90°	0-90°	0-90°	0-90°	0-90°	0-90°
Working Current	0.25A	0.48A	0.68A	0.8A	1.2A	2A	2A	2.7A
Starting Current	0.25A	0.48A	0.72A	0.86A	1.38A	2.3A	2.3A	3A
Drive Motor	10W/F	25W/F	30W/F	40W/F	90W/F	100W/F	120W/F	140W/F
Product Weight	3kg	5kg	5.5kg	8kg	8.5kg	15kg	15.5kg	16kg
Voltage Option	AC 110V, AC 220V, AC 380V, DC 12V, DC 24V
Insulation Resistance	DC24V:100MΩ/250V; AC110/220V/380V: 100MΩ/500V
Withstand Voltage	DC24V:500V; AC110/220V:1500V; AC380V:1800V 1Minute
Protection Class	IP65
Installation Angle	Any
Electrical Connection	G1/2 Water-proof Gable Connectors, Electric Power Wire, Signal Wire
Ambient Temp.	-30℃to 60℃
Control Circuit	A: ON/OFF type with light indicator signal feedback
	B: ON/OFF type with passive contact signal feedback
	C: ON/OFF type with resistance potentiometer signal feedback
	D: ON/OFF type with resistance potentiometer and neutral position signal feedback
	E: Regulation type with servo control module
	F: DC24V/DC12V dirct ON/OFF type
	G: AC380V three-phase power supply with passive signal feedback
	H: AC380V three-phase power supply with resistance potentiometer signal feedback
Optional Function	Over Torque protectors, dehumidify heater, stainless steel coupling & yoke

3D Display of Electric Valve:

Installation Precautions:
● Before installing the valve, clean the line of dirt, scale, welding chips, and other foreign material Clean gasket surfaces thoroughly to insure leak-proof joints.
● Verify that the valve breakaway torque is less than the rated output torque of the actuator.
● Any mechanical stops that would interfere with the operation of the actuator must be removed before installation of the actuator, i.e. lever, travel stops, etc.
● The actuator output coupling must be centered with the valve stem to prevent side loading, which causes premature stem packing wear.
● To use the manual override feature (identified on cover label), the override shaft must be pressed down firmly at least 1/4" in order to disengage the motor from the gears. The manual override is not designed to overcome torque in excess of the rated torque of the actuator. Serious damage to the gear system may result from excessive turning force on the manual override.
● This Series actuator may be mounted in any position, i.e. horizontal, upside down. If the conduit entrance points upward, conduit piping must be oriented as to prevent condensation from enteringthe actuator from the conduit pipe.

Installation environment:
● The product can be installed indoor and outdoor, The surrounding environment temperature should be in -30°C~+60°C
● Product is non-explosion-proof production, and the installation must be avoided being in flammable or explosive environment etc.
● The actuator should be in protection box in the environment of long-term with the splash of rain, material and direct sunlight.
● Please reserve space for controller, manual operation.
★ The surrounding environment temperature should be in -30°C~+60°C.

Installed on the valve body:
● Manually operate the actuator to drive the valve, confirm it does not have abnormal situation. Turn the valve in full closed position.
● Assemble the bracket to the valve body.
● Set one end of couplings on valve spindle.
● Turn the electric actuator to full closing position, and insert output-input shaft into the square holes of couplings.
● Set the screw between the electric actuator and bracket.
● Turn actuator by hand shank, confirm that it moves translation, no eccentric, no skew and no overrun.


Cable installation:
● Install wire tubes, The outside diameter of wire tubes should be $9-411. Take measures to proof water. To prevent actuator from flowing into wire tubes water, the actuation position should higher than wire tubes position.
● When installing wire, the outside diameter of wire should be $9-φ11. in case the water flow into actuator interior from line locking, all wire that are not allowed to be used.
● The signal wire should be shielded wire in principle, don't parallel it to power wire.

Special tips:
● Caution: can't connect one actuator parallel with one another, in other words, can't use the same controller contact point to control more than one actuator, otherwise it will cause out of control, motor overheating, product damage, shorter service life.
● If the actuator is installed outdoor, we suggest equipping other protective cover to proof water, stabilize mechanical property, make a longer service life.